Home | Gallery | Forums | Ads | Store ANTIQUETRACTORS.COM

PartsASAP LogoCompany Logo Antique Tractor Resource Page

   Allis Chalmers Case Farmall IH Ford 9N,2N,8N Ford
   H. Ferguson John Deere Massey Minn. Moline Oliver

Marketplace
Tractor Manuals
Tractor Parts
Engine Kits
Classified Ads
Photo Ads

Community
Discussion Forums
Collector Profiles
Show Guide
Guest Book

Galleries
Tractor Photos
Implement Photos
Vintage Photos
Help Identify
Parts & Pieces
Stuck & Troubled
Vintage Ads

Research Center
Tractor Values
Production Numbers
List Prices
Tune-Up Specs
3-Point Specs
Spark Plug List
Torque Values
Torque Specs
Plow Specs
Terminology
Clubs & Pubs
JD New Generation
JD HP Chart

Miscellaneous
Today in History
Pic of the Day
Table of Contents

Related Sites
Garden Tractors
The Tractor Shed
Ford 9N/2N/8N Club
Yesterday's Tractors
More Sites

Tractor Stories

Return to List

Popeye the Ford 600

About twenty years ago My brother bought a sad looking 600 Ford on the back line of a construction auction. It had a sweeper on it and appeared that it had not run in a while. We brought it home and cleaned the points and plugs and put gas in it. It would not crank with the starter so we pulled it off and it cranked. It smoked badly and had a great deal of back pressure. We pulled it apart and the cylinder walls and bearings looked good. We are thinking that all it needed was a set of rings and without any marks on the tops of the pistons we made the 'assumption' that it was standard bore. When the rings came in I took one out and put it in the bore to check the end gap. Huge gap apparently they had given us the wrong rings so we took them back and parts man said they were right for a standard bore 600. Went back and measured it and found that it was only a few thousandths from being 4 inches instead of 3 7/16 as it should. Went back to parts place and they had nothing listed for that size bore. The parts man looked it up by size and got us a set of rings for a GMC six cyl. I had to file the rings to the get the right end gap and put it together. It ran good and had lots of power. We had almost made the same mistake that the previous mechanic had and installed the wrong rings. It was a good little tractor and we used it at the hunting club and gardening for several years. It only had one headlight and it was affectionately named Popeye.

Ron, SC, entered 2013-01-24
My Email Address: Not Displayed

Return to List


TRACTOR PARTS TRACTOR MANUALS
We sell tractor parts!  We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today. [ About Us ]

Home  |  Forums


Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy

TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters

Website Accessibility Policy