(800) 853-2651
SHOP NOW

Deere LI Foot Throttle Linkage to Carb

C

climbergy

New User
Can someone please shoot me a few pics showing the linkage from the foot throttle to the carb on a Deere LI? I believe I have all of the parts (Pedal, 2 rods, a spring, and a small angle mounting bracket), just not sure exactly how they go together and where the rod connects to the carb as I assume the rod from the governor still needs to be connected. Much appreciated. Want to get it mounted ASAP for a coat of paint tomorrow. Thanks in advance!
 
(quoted from post at 21:00:57 05/24/17) Can someone please shoot me a few pics showing the linkage from the foot throttle to the carb on a Deere LI? I believe I have all of the parts (Pedal, 2 rods, a spring, and a small angle mounting bracket), just not sure exactly how they go together and where the rod connects to the carb as I assume the rod from the governor still needs to be connected. Much appreciated. Want to get it mounted ASAP for a coat of paint tomorrow. Thanks in advance!
Click to expand...

I understand this half of it, would appreciate photos from the spring to the carb.
49135.jpg
 
I just put one of these together. I tried to take a picture but there isn't a good angle for a picture. But the rod attaches to a hole in the governor arm below the pivot point. The hole is towards the rear of the arm. The little bracket attaches to a screw the holds the hood assembly on, just ahead of the hole that rod goes through. Once you look at it you'll see there aren't any options. The bracket keeps the rod from rubbing on the hole through the hood. Hope this helps.
 
I think there are two different configurations for LI, early with Hercules and later with JD.

Talk with Steve @ Ridenour, he has all the parts needed
 
(quoted from post at 00:55:26 05/25/17) I just put one of these together. I tried to take a picture but there isn't a good angle for a picture. But the rod attaches to a hole in the governor arm below the pivot point. The hole is towards the rear of the arm. The little bracket attaches to a screw the holds the hood assembly on, just ahead of the hole that rod goes through. Once you look at it you'll see there aren't any options. The bracket keeps the rod from rubbing on the hole through the hood. Hope this helps.
Click to expand...

Thanks again for the help. Just want to confirm the correct placement of foot throttle rod as pictured. Does the hand throttle cable then attach to the other lever hole? What mounts to the empty bracket coming off the block? Pics always worth a thousand words, but I'll take whatever I can get.
 
You must log in or register to reply here.

Similar threads

G
1935 B throttle linkage ?
Replies
2
Views
215
Mike M
M
N
S77 Throttle Linkage
Replies
1
Views
327
John Schoenauer
J
J
fORD 1700 hand and foot throttle linkage
Replies
1
Views
285
used red MN
U
K
1020 throttle
Replies
5
Views
506
Jim.ME
J
L
1987 John Deere AMT 600 Governor and Throttle Linkage
Replies
0
Views
116
lostpeacock
L
Tractor Parts Tractor Manuals

We sell tractor parts! We have the parts you need to repair your tractor - the right parts. Our low prices and years of research make us your best choice when you need parts. Shop Online Today.

Copyright © 1997-2024 Yesterday's Tractor Co.

All Rights Reserved. Reproduction of any part of this website, including design and content, without written permission is strictly prohibited. Trade Marks and Trade Names contained and used in this Website are those of others, and are used in this Website in a descriptive sense to refer to the products of others. Use of this Web site constitutes acceptance of our User Agreement and Privacy Policy TRADEMARK DISCLAIMER: Tradenames and Trademarks referred to within Yesterday's Tractor Co. products and within the Yesterday's Tractor Co. websites are the property of their respective trademark holders. None of these trademark holders are affiliated with Yesterday's Tractor Co., our products, or our website nor are we sponsored by them. John Deere and its logos are the registered trademarks of the John Deere Corporation. Agco, Agco Allis, White, Massey Ferguson and their logos are the registered trademarks of AGCO Corporation. Case, Case-IH, Farmall, International Harvester, New Holland and their logos are registered trademarks of CNH Global N.V.

Yesterday's Tractors - Antique Tractor Headquarters
Website Accessibility Policy

Back
Top